Inside this building, more hygienic, less humid and moist, warm environment that we provide for our building walls very will be healthier. There s paint, gypsum plaster in your Bloom or spills, in your heater in the drywall behind bottom mold is eliminated this way.

Fuel your spending, lowers the average 50% during the winter months.
Less fuel, more allows you to warm up.
During the summer, prevents overheating of the place you live.
To cool off significantly reduces the electric consumption.
Creating a balanced room temperatures comfortable and creates healthy living spaces.
Black mold caused by humidity, fungus and prevents stains.
Prevents rusting of iron within the concrete, building resilience against earthquakes.
Environmental pollution and contribute to prevent global warming.
Besides, efficiency, reduce our nation s dependence on foreign energy.

Tiled ceramic tile breakage, spillage, over time in blistering, cracking like deformations occur.

• Causes of distortion;
• The origin of the application
• Structural welded
• Production of welded
• The inaccuracies resulting from use
• Wrong choice of materials
  
  

Because the application of practices, as in the case of the laying of jointless coating due to the expansion after a while tile bristling spills will occur.

Especially because prior to the application of ıslatılmaması wall tiles wall tiles be poured by leaving in the adhesive.

Cladding into the adhesive mortar, for example an external material of cement based adhesive into the plaster, lime, clay, sand, material strength of materials such as will again reduce the deformation will result.

In particular, the use of bonding and fuga mortar Cap life and not pay attention to the main reason for the distortion again while dredging is one of.

Production, resulting in error are usually the product with the introduction of an external material from the outside to the inside. It is a condition that will identify the manufacturer.

Resulting from errors on use; for home users, especially while cleaning of ceramic tile, bleach, hydrochloric acid exposure as high as supplies to clean up the surfaces of materials, grouts to cause wear and tear after a while he got up from all over, even after some time of broken.

Structural error, especially close to the occurrence of water installations and points, in ceramic tiles along the cracks.

The junction point of the crosshead or at the point where the wall in kolanla, corresponding to the point at the junction of two different building materials, ceramic tile in, due to the different materials work in time along the cracks.

External venues especially in choosing the wrong adhesive coating is used, combined where it should be done by the method of application, especially don carding patlağına, raised and caused flaking.

This and similar in a lot of their why ceramic tile, breaks, spills. Why not, previously diagnosed with the right materials, accurate diagnosis, the surface of the material is very important in the right place.

Ponds, baths, water tanks, such as wet areas, ceramic tiling and escape from before out of the water in the water should be prevented. That s why in these regions before the ceramic coating with the right insulation materials are waterproof. Inroads this kind of applications, ceramic Alfix pool, pool and wet adhesive mortar for floors should be preferred. Ceramic high-performance again on the sidelines of the Alfuga Pool, pool and must be filled in with a wet Joint Filler Material for floors.

The terrace and balconies is constantly outdoors exposed to atmospheric influences. Rain, snow, cold, hot, corrosive effects on wind-exposed ceramic tiles laying the right ingredients with the right techniques. Which will constitute the top tier ceramic tile adhesives, absolute way when coating application techniques using high-performance adhesives are required.

Resistant to both heat and water-resistant conversion and frost-resistant, this can be done only with long lasting adhesive coatings.

Grouting materials is both water resistant and resistant to heat and cold.

Coating will be used as the standard tooth measures will surely way big must be selected.  Application should be made in the method of combined, so the adhesive mortar should be applied and kept both surface comb and ceramic tile should be applied and kept the rear surface of the comb.

Mortar bed placed tile will surely way before printing by hand, it should be installed at a later time, rather than by applying the plastic with a good-sized plastic with a very good tokmaklanarak.

Coating will be dropped at the size of the width of the ceramic tile grouts and to be resistant to thermal conversion must be selected.

Especially in the wide terrace footprint expansion joints should be also. Expansion joints can be filled with such nomination with sealant.

Will constitute the gold overlay is strong enough and should be made a smooth incline enough screed. This material is very important for the water to the bottom of the entry. Water goes into the slope should be set very well. Especially on the terraces and balconies with don patlağ. The main reason for this is that water is entering the bottom of the coating and cold weather.

Therefore, the coating should be absolute water under the entry way. The easiest and best way to avoid this, take very good filling of joints, use of a water resistant material and coating the absolute way through pass to be combined. It is insulated with don patlağ if done.

In wet ceramic tile surfaces prior to coating the preparation is very important. Vertical surfaces, solid and smooth surface, there is a need for an absolute way to obtain excellent adhesion. This plaster with cement lime DOSER joining 400 prepared plaster. This plaster must be in every point in the infinitive. Rude waterproofing compounds is very good in terms of adhesion release will give you the results. In order to prevent cracking of the plaster, more even-strength Allmax into Latex, Bonding off wall Enhancer can participate in the Mortar and Additive. Vertical surfaces, underlay much experimentation that we have done for horizontal surfaces s properly the spanking.

Another issue is to know in wet insulation against water. Because ceramic tiles are all by themselves will not be able to show an insulation against water. Although the back of the front surface of ceramic tiles surfaces of waterproofing wet areas such as bathrooms, although especially waters can enter under the coating. Entering point is usually the point where ground water from creeks or wall switch.

They have a few small details left to do to make sure this doesn t happen. These are at the beginning of isolation. Insulation for cement-based waterproofing mortar or acrylic sealing mortars can be used. Application of brush or rolls of these products as well as through the flat part of the comb trowel 1-2 mm thickness can be applied to the surface in the shape to be created. At this point, the most important issue to be considered, where the wall point especially during floor insulation file supplement. Here at the junction of the two walls as vertically still needs to be done with the file supplement will give very good results the isolation. The use of insulation materials and driving patterns, it is necessary to note.

Another issue is joint. There s water in wet, prevent weathering and as it is known in places where mold too. Therefore we will use in wet, mold and algae within normal standard gap when.

To avoid this, do not make a mold resistant fungs, cracking, smooth surface that can create a silicone based Alfuga Ultra silicone Grouting Material using such products will give you much better results.

These types of applications Grafix Flex II, dual-component Flex Granite-Ceramic adhesive mortar or Allmax Latex, Bonding and off wall Enhancer Mortar Additive powered, high performance flexible adhesives should be preferred. Certainly when application double sided adhesive method should be preferred. Now a lower-order resistance won the top changed

Granite ceramic tiles are very low water absorption rate with high strength Tile. High performance adhesive mortar to be used in the application shall must be absolute in adhesives C2 class. Stoneware pieces of standard C1 class adhesives adhesives should not be used. In practice, the most important issue to be considered is to use the notched trowel is a measure of the teeth of steel. Granite ceramic tile sizes will be chosen according to the size of the teeth must be greater as possible. Granite ceramic tile has size, EUROMOT 3 engine less tooth size none notched trowel with döşenmemesi. 8 x 8 x 8 or grating discs mm should be applied with notched trowel with steel gear. Still another issue is also to be aware of application foundation piles will be used during the gavel is light-colored. In other matters, the application also must make absolute thereby combined method with the coating.

Reuse existing old ceramics ceramic needs a number of requirements for kaplayabilmek. The most important of these existing old ceramics must be solid.

This is no place to check the solidity of the hand can be also place a plastic with a ceramic tile can be polled. Tarak, suspected, or non-ceramic tiles, first over the plug even this ceramic paste at the bottom of the harcıda is not removed from there, that harçta appropriate solid repair with these places are to be filled.

After other important terms of this leveling of the joints with the existing old is required to be furnished.

If the existing old ceramic, grout is furnished in this case all of the existing old ceramics without hesitation ripped again by plaster repairs should be done and on the Corporation s existing plaster should be made of ceramic, such as ceramic coating.

Therefore, the application of a zero joint over a ceramic tile ceramic tile line is not going to have the correct results.

Another important respect, ceramic glaze layer in front of the surface. If the coating cement-based, adhesive mortar is used be sure way old ceramic layer of secrets located on the surface of it is necessary to get rid of. Otherwise, the cement-based bonding mortar surface water absorbency of surfaces grip capabilities directly proportional to. Glazed ceramic tile to the front surfaces of water to cement-based paste em mortars do not hold very well on this type of surface. Therefore, old ceramic of secrets at frequent intervals should be drawn. The best way to do this was possible, angle grinder machine secrets of existing old ceramic 45º C to be the angle of the existing field at frequent intervals over 70% more should be drawn.

While this is in progress, check this out too. Spiral stone engine in front of the knife too much deep daldırılmamalıdır. So we should not be wasting the back surface bonding of ceramics.

Should be taken only of the front surface 2 mm layer of glaze. While this is in progress a lot of mistakes, not hammer while secrets are secrets. This is an incorrect behavior. Because while this process without realizing it, we compromise the existing old ceramics. Therefore, we should not use the process certainly attractive notch.

Another important issue is the full scale of the existing old ceramics and really should pay attention to in the infinitive. To do this, with the help of a surface gauge and scales should be checked from different locations. Similarly, it must be in the full internal and external corners, miter.

After the surface layer of glaze surfaces plenty of dust. After a brush with this powder adhesive unglazed surface to increase the surface aderan Betomax UNI, Multi-purpose Performance Insole or Primerfix 101, smooth surface Coating will benefit ride.

Ceramic on ceramic prior to the application, and ensure that existing ceramic robust surface to be applied in the case of surface water will not be exposed to direct all the time Primerfix 101, smooth surface Coating may be applied. Gluing cement based or in acrylic-based, high-performance, flexible adhesives should be preferred.

Additional considerations in implementing a matter at the surface of the comb the adhesive grip angle. In terms of normal grip comb slightly lower angle. When we pull the comb teeth are a problem of the old occurrences of points in ceramic.

Water-based painted surfaces, the paint is solid and his folly in the surface of ceramic tiles in case of believe, move these surfaces a suitable primer materials, coating can be used before.

Painted surface stability, no doubt detachable, water-based or solvent-based paint painted surfaces with any ceramic tile coating is not going to have the correct results. Therefore, in these cases, we need to get rid of paint is one way.

There are several ways of getting rid of anything besides, the easiest and the simplest of these is to dig below the surface. But in any case this stripping may not occur. The main reason we scraping the paint from the surface; tutunabilme on the surface of the paint. This will make the surface normal power, ceramic tile bonding is very very low.

Water-based paints are replaced once a year, 4-5 4-5 and froth is poured or color a year or so, solvent-based paint is a little more of life is long. But ceramic tile life with these absolutely incomparable. Without any preparation is cover the ceramic tiles, ceramic tile directly over the life cycle, we synchronize the life of the paint. Therefore, when the paint begins to rise, getting up from the ceramic tile be poured with our State. That s why we need to get rid of paint before you start from hull.

This is the most practical way to hammer surface notch. This is a very technical process of notching. The hammer was not the upright pommel, pointed to the surface with a pain for nearly 30 -35 only to surfaces in their weight should be shot. An extra power should not be applied. In this way we can create nicks at frequent intervals on the surface. It s like we can do it this way, we can draw on the surface of the stone or the Palm of the surface paint on the dig. This will be much more practical and much more series. But there will be a lot of dust in the environment.

Therefore the surface after you surface spalling and boot taken later before the dust with a brush to the surface again Betomax EM2, absorbent Surfaces for acrylic-based primer or Betomax UNI, Multi-purpose Performance should be Lining. The main purpose here, so holding and adherence between the surface with glue is to enhance the Eclipse.

Another important issue is the comb used grip angle. Normally, ergonomically comb 40 -45 °-50-55 ° at an angle. But when we use a painted surface of the comb ceramic wrap our grip we need to reduce the angle is a little more than normal. The aim here is to leave more adhesive on the surface. This is the angle at which we need to zero or close to zero while lowering full hold. We can t get enough depth of teeth or. Therefore a slightly lower angle from the normal grip if we leave more mortar on the surface.

Compare here should be, must not interfere or the following painted layer of the comb passes through a layer of plaster, gözükmemelidir. We can take this base.

Of course, the painted surface before plating on surface of scales is in the infinitive are other important points. Also be used still coating adhesive mortar, high strength, flexible adhesives. In addition, under normal circumstances, made after 24 hours in coatings joint fillers, these types surfaces only side, bottom paint, adhesive mortar will extend dry time surfaces of as late as possible, 3-4 day, whenever possible, in fact, must be made within 5 days of the grout.

In some cases, you may need to cover ceramic tiles on gypsum plaster. To do this, it is necessary to arrive at a number of requirements. First of all you must have a solid gypsum plaster available. The second fundamental conditions, gypsum plaster is required to be in full our scales. Gypsum plaster, scale and gauge should be checked, if it is necessary to rectify if there were any deviation. Repair these surfaces with the first sıvanmalı then hull. If you have any problems in our plaster or coating can be done directly.

Gypsum plasters, especially gypsum are basically water and water vapor are the material against the weakness. More moisture in the environment can reduce the moisture to the site that has the ability to give back to the environment moisture again. Therefore, before the plaster cement waterproofing compounds we wet it with water as it is will not be correct. Therefore they plaster acrylic based Primer for Absorbing Surfaces EM2 Betomax, Betomax, or UNI, primed with Multipurpose Performance Lining. This primer is a liquid material. To paint with a brush is applied to the surface. Primers have been applied, depending on the ambient conditions can be implemented after 40-60 minutes.

In some cases if the stability of the doubt cast on this case surface nicks opening centrepiece is recommended. This notch should regular hammer. We hit it with a hammer regular gypsum much experimentation inevitably are certain points we can undermine without realizing it.

In this case, hammer instead of an angle grinder and at certain points we can draw much experimentation, plaster. After this process, I m sure there will be a lot of dust in the environment, these powders after coating application and receipt.

Application of high-strength adhesive mortar to use absolute way, must be a flexible adhesive.

Another important issue is the most important point is to know in plaster, perhaps, is the carrying capacity. Gypsum plasters, normal cement plaster for more strength according to the material. Therefore, there is no too much carrying capacity. In this case we occupy on gypsum plaster ceramic tile with adhesive mortar m² under the falling weight does not exceed 25-27 kilogram is required.

Buddha means that very large, very thick materials on gypsum plaster coating will not be right. If you are prompted for gypsum plaster coating from the surface must be a cement plaster again scraped and plating.

Ceramic tile with a flat surface coating operations put hand trowel adhesive to steel notched trowels leveling of technologies used. This steel notched trowels have different forms of teeth tooth size, mala. Notched trowels with square gear usually used in our country. This 4 mm x 4 mm x 4 mm notched trowel for example in, 6 mm x 6 mm x 6 mm, 8 mm x 8 mm x 8 mm, 10 mm x 10 mm x 10 mm notched trowel with a width of.

To help you determine where to use which notched trowel, we use ceramic tile is the most important factor in hull the size factor. Ceramic tile size increases, the size of the tooth comb will use measurement increases.

For example; 20 x 20 size when a Tile ceramic tiling, EUROMOT 3 engine mm will do when a tile when tiling, 60 x 60 size 8 x 8 x 8 mm notched trowel or we are required to use the grating discs mm.

Other than that the raker tooth size and circular shape which is shaped like a pyramid as a way available in the comb. More round used in the marble coating process. Triangle notched trowels gear, these are more of a small-sized tiles may be more useful in applications.

Another factor influencing the selection of a comb, surface smoothness. Very rough, very rough surfaces such as plaster, raker tooth the size of a normal upper would be more appropriate to increase, will better leveling the surface. Smooth surfaces can be undertaken on a lower level.

Comb ceramic tile that is used the most important when choosing the size of the error made is ignored.

The main reason of our wet coating we use the tile in cement based adhesive harçlarıdır. We know that using cement based adhesive mortar cement based adhesive mortars, cement will be needed due to the water. To be able to maintain hydration cement you need enough water. If the application will be made on the ıslatılmamış tile adhesive glue tiles that we will want to absorb the water quickly. Therefore, it is necessary to water the cement harden. In this case the surface of the ceramic tile with adhesive mortar adhesion adhesion between impairment will occur, and after a while, ceramic wall tiles so they will rise before the tiles then covered place.

Coating cement-based adhesive mortar be used tiles, ceramic wall tiles to be soaked in the certain way.