Windows, profiles and glass exterior air into the atmosphere, they are direct parts worth inside forwards a lot of cold and heat rate. Their thermal conductivity is used to abate profile material is very important and double glass minimizes the heat out in the application, such as Exchange.

But other than that, the system in the profile and the largest remaining after missing the solution on the glass this window of exterior walls and floors of reinforced concrete brick, plaster and is the joints. Different materials showed different behavior under the Sun ultraviyolesi search of properties in order for you to work in flexible sealant fills etc must be done towards the end of the same with material application type sheathing systems or compact laminate cladding systems, window and the side wall of the importance in the details you ll need to show the same combination.

Application surface dust, oil, paint, curing agents, detergent, like preventing mould oils and silicone materials thoroughly. If you have surface paints and plaster kabarmalar in this region before are thoroughly cleaned, cracks and defects should be repaired. Surface preparation can be applied only after the completion of the surface coat of primer. After you have completed the entire surface preparation, coating application is completed.

Zeminimiz and of course a reinforced concrete ceiling plate and concrete bricks, transmits more than cold and heat. That s why the outside indoors with the necessary heat insulation between floors in addition to a heat insulation purposes of parquet etc provide flooring you can use thermal insulation under the shields and thermal insulation under screed the floor plate is also available with a thermal insulation barrier.

But it must be remembered that when it hits a grading in terms of exterior taken outside to the front of this apron outside to suck cold passes a heat insulation, jacketing system. Otherwise it s just a heat insulation on the wall from the inside with you cannot log off the cold that will run to the ground.

There are 2 different bonding technology according to the surface.

1-Heat insulation panels in all of the Ribbon to the edges and the middle section with thermal insulation Plate in point trowel adhesive mortar.

2-thermal insulation plate a trowel or notched trowel appropriate to the entire thermal insulation Sheet with an adhesive mortar.

Thermal insulation plaster on the absolutely sponge should not be fired. Süngerleme process that aggregated within the plaster plaster causes crack by lost strength. Instead made firm enough to plaster trowel scraping after drying.

Our basement walls of condensation water in contact with Earth to cut the outside of the basement walls, you ll need a base under the thermal insulation. In the same way water pump bad, so the exterior of the building wall heat insulation. This can occur if the temperature difference in the inside and out and the flow of heat, all the condensation dezasyon water.

Even years later after the buildings heat insulation, it is possible to make. To do this, called technical coating. This method of your building with polystyrene plate or Rockwool. Mantolamanın effect is less if done later on, there is no such a rule. But the use of the correct detail and accurate material is required.

Reduces your fuel consumption by an average of 50% during the winter months.

With less fuel, it allows more heat.

In the summer months, it prevents overheating of the place you live in.

It significantly reduces the electricity costs you make for cooling.

It creates comfortable and healthy living spaces by creating balanced room temperatures.

It prevents mildew, mushroom and black stains caused by moisture.

Prevent the corrosion of the iron in the concrete, protect the durability of the building against the depression.

It contributes to environmental pollution and global warming prevention.

With the efficiency you have, it will reduce your country s external dependency on energy.

Heat losses that occurred in winter and in summer to reduce heat gains occurring process called "thermal insulation". In the winter cold for coal, natural gas heats our House using such fuels; in the summer heated House air conditioner soğuturuz with.

Warm up in the winter and in the summer, heat insulation, to cool off, reducing the energy we spend more in order to live in comfortable surroundings. In this context, the thermal insulation of buildings not heated warehouse outside or garage, facing the wall, roof sections, trim, glass, joinery, and is applied to the installation.

In other words, building heating by using less energy, or of the inhabitants of serinlemesi and hence ensure the reduction of environmental pollution, preserving the building s internal and external factors for the purpose of extending its life; different temperatures to reduce the passage of heat between the circumference with living spaces for operation is called "thermal insulation". (İzoder)