MULTI-PURPOSE PERFORMANCE ENHANCING PRIMER
Product Description:
Acrylic-based, multi-purpose performance-enhancing primer material that can penetrate into the concrete screed or plastered surfaces it is applied to, and eliminates the absorbent properties of these surfaces.
Public Works Pos No: 04.503/1
Areas of Use:
Indoor and outdoor,
In horizontal and vertical applications,
On absorbent and impermeable surfaces,
Fixing absorbent and dusty surfaces and eliminating their absorbent properties,
To increase adherence first in adhesive, plaster and decorative plaster applications,
In order to increase adherence before the applications to be made on old surfaces,
Gypsum, aerated concrete, chipboard, briquette, etc. protecting water-absorbent surfaces from moisture,
As a primer before paint and wallpaper applications,
In preventing the dust of the screeds on which carpet will be laid,
It is used to form an insulation layer, to increase adherence, to prevent dusting, to prevent foam and cracking before the application of materials such as waterproofing mortars, leveling screeds.
Features:
It is easy to apply.
It is suitable for multi-purpose use.
It is water-based, odorless, and can be safely used indoors.
It removes the absorbency feature of the absorbent surface. Thus, it prevents the loss of necessary hydration water in the mixture of cement-based materials to be applied on it.
Provides high adherence, prevents dusting.
It is applied before cement-based coatings to be applied on absorbent surfaces, preventing rapid water loss and air bubbles that may occur in the screed.
It provides the formation of an insulation layer before waterproofing mortars.
Increases workability.
Provides moisture resistance.
Technical Spesifications:
Appearance: White liquid
Density: ~ 1,05 kg / liter
Application Temperature: + 5ºC to + 35ºC
Drying Time: 45-60 minutes
Second Layer Application Time: 60-90 minutes
Service Temperature: -30ºC to + 80ºC
The above values are given for +23 ºC and 50% relative humidity.
Pre-Application Preparation:
Must be taken care that the application surface has cured. The application surface must be cleared of dust, oil, paint, curing material, detergent, mold oils and anti-adhesion materials such as silicone.
Application:
Betomax Uni, Multi-Purpose Performance Primer is a ready-to-use primer. It is mixed thoroughly before use and applied in two layers with a brush or roller.
If necessary, it is diluted with water at the rate of 1/1 while applying the first layer, and applied without thinning in the second layer.
The drying time of the product is approximately 45 - 60 minutes. If it is to be coated, it is coated before the primer is completely dry.
If it will be applied on floors with floor heating, the heating should be turned off during the application. In winter, the heating system should be kept between 15 - 18 ° C.
Warnings:
Avoid application in areas that are frozen, have a risk of freezing within 24 hours or are open to direct sunlight and wind.
Consumption: 100-200 gr/m²
It varies depending on the application surface.
Packing: 10 kg. plastic bottle
Storage and Shelf Life:
Protect the liquid component from exposure to sunlight and frost between + 5ºC and + 35ºC.
Shelf life is 12 months in its original packaging in a suitable environment.
Safety Advices:
For more detailed information, please refer to the Safety Data Sheet.
Responsibility:
The application instructions and technical values given in this technical document are based entirely on our scientific and practical knowledge. These values may change depending on the ambient conditions. Allmax Construction Chemicals reserves the right to make changes in products in line with technological developments. Allmax Yapı Kimyasalları cannot be held responsible for the results that may arise out of written recommendations regarding where and how the product will be used and / or due to incorrect use. Therefore, when using Allmax Construction Chemicals products, make sure you use the right product in the right place. Allmax Construction Chemicals is only responsible for the quality of the product.
