CEMENT BASED SATIN PLASTER
Product Description:
It is a satin putty based on white cement, with improved workability with polymer and chemical additives, used to obtain a smooth surface to prepare the surface for paint after the final layer of plaster, which can be applied by hand.
It is suitable for TS 7847 and TSE EN 998-1 (GP) standards.
Public Works Pos No: 04.476/D
Areas of Use:
Indoor and outdoor,
On the wall and ceiling
Especially on concrete, rough plaster, fine plaster and mineral-based surfaces,
In the correction of fine cracks on the surface,
It is used to obtain a smooth final surface before painting.
Allmax Satin GP:
In exterior cladding plates,
It is used to obtain a smooth surface in thermal insulation systems.
Features:
It is applied by hand.
Provides a smooth surface.
It is applied easily and without cracks on large surfaces.
It is resistant to water and frost.
Allmax Satin GP:
It has higher adherence and durability than gypsum and gypsum-based materials.
Despite the fact that plaster is easily affected by moisture, moisture, moss, dust etc. eliminates the problems.
It reduces paint consumption.
Suitable for wet areas and repairs.
Technical Specifications:
Appearance: White Powder
Dry Unit Weight: 1100 ± 200 kg / m³
Application Temperature: + 5ºC to + 35ºC
Water Mixing Ratio: 6.5-7.5 Liter / Bag
Rest Time of Mortar: 5-10 min.
Pot Life: ~ 1 hour
Applicable Thickness: 1-3 mm
Drying Time: 24 hours
Temperature Resistance: -30 C to + 80 C
Dry Film Thickness: > 400; E5
Grain Size (mm): <300; S2
Water Vapor Transfer Rate, g / (m2.day): V0
Water Transfer Rate, kg / (m2.hour0,5): W0
Crack Covering: A0
CO2 Permeability: C0
Resistance to Mold Growth: K2
Compressive Strength: CS IV: ≥ 6 N / mm²
Bond Strength: ≥ 0.25 N / mm² (FP: A)
Capillary Water Absorption: W0
Water Vapor Permeability Coefficient: µ ≤ 25
Reaction to Fire: A1
The above values are given for +23 ºC and 50% relative humidity.
Pre-Application Preparation:
Care must be taken that the application surface is cured and solid.
The surface must be free from mold oil, dust, paint and adherence reducing materials.
Before the application, the repair of cracks and holes should be done with suitable repair mortars.
If necessary, the application surface should be moistened with water.
Measures should be taken against dusting on plastered surfaces.
Application:
20 kg. Allmax Satin is poured into a container filled with approximately 6.5-7.5 liters of water and mixed with a low-speed mixer or trowel until a lump-free mixture is obtained.
During the mixture, any additives not specified in the application instructions should not be added.
The prepared mortar is 5-10 minutes. Let it rest for maturity and again 1-2 minutes. It should be mixed until it becomes homogeneous.
The prepared mortar should be applied to the entire surface with a steel trowel in equal thickness.
After the application, the surface should be smoothed with a finishing trowel.
If more than one layer is to be applied, the second layer is applied as a thin layer and polished after the first layer has hardened. Total thickness should not exceed 3 mm. A net should be used in thicknesses to be exceeded.
After the application, the surface should be moistened for 2-3 days.
After the complete drying time, a fine sanding can be used to obtain a smooth surface.
Warnings:
No foreign material (lime, cement, gypsum, etc.) should be added in the prepared mortar.
The expired mortar should not be mixed with water or dry mortar and used again.
Satin plaster application should be done at least 7 days after the plaster application.
It is recommended to apply at a temperature between + 5ºC and + 35ºC.
In windy weather, the mortar should be protected against rapid drying.
It should not be applied on frozen surfaces.
It is recommended not to apply under direct sunlight.
Do not go beyond the specified application surface and usage instructions.
Consumption: 1.00-1.50kg / m² (for 1 mm thickness) The consumption amount is theoretically calculated values in the laboratory environment; We recommend that consumption control sample application be made before the application.
Packing: 20 kg craft bag.
Storage and Shelf Life:
It should be stored in its unopened original package, in a cool and dry environment, protected from frost. For short term storage, maximum 2 palettes should be placed on top of each other and the shipment should be made on a first in, first out system.
Palettes should not be stacked on top of each other during long term storage.
It is 12 months from the date of production under suitable storage conditions. Opened packages should be stored under appropriate storage conditions and used within one week.
Safety Advices:
For more detailed information, please refer to the Safety Data Sheet.
Responsibility:
The application instructions and technical values given in this technical document are based entirely on our scientific and practical knowledge. These values may vary depending on the ambient conditions. Allmax Construction Chemicals reserves the right to make changes in products in line with technological developments. Allmax Yapı Kimyasalları cannot be held responsible for the results that may arise out of written recommendations regarding where and how the product will be used and / or due to incorrect use. Therefore, when using Allmax Construction Chemicals products, make sure that you use the right product in the right place. Allmax Construction Chemicals is only responsible for the quality of the product.
