CEMENT BASED READY-MADE FINE PLASTER
Product Description:
Cement-based ready-to-use thin plaster applied on coarse and ready-made cement-based plaster applications, indoors and outdoors.
TS EN 998-1
Public Works Pos No: 04.476/C
Areas of Use:
Indoor and outdoor,
On the wall and ceiling
On gross concrete surfaces,
It is used on rough plaster and ready cement based plaster applications.
Features:
It is applied by hand.
It is resistant to water, frost and moisture.
It breathes and balances the humidity by allowing evaporation.
It has a plastic consistency and is easy to apply.
It gives a smooth surface for the final coating.
Technical Specifications:
Appearance: Gray Powder
Dry Unit Weight: 1400 ± 300 kg / m³
Application Temperature: + 5ºC to + 35ºC
Water Mixing Ratio: 5.0-6.0 Liter / Bag
Applicable Thickness: 3-10 mm
Drying Time: 24 hours
Compressive Strength: ≥ 6 N / mm²
Bond Strength: ≥ 0,2 N / mm²
Capillary Water Absorption: W0
Water Vapor Permeability Coefficient: µ ≤ 25
Average Thermal Conductivity (W / m.K): ≤ 0.93
Reaction to Fire: A1
The above values are given for +23 ºC and 50% relative humidity.
Pre-Application Preparation:
The surface must be free from mold oil, dust, paint and adherence reducing materials.
Before the application, the repair of cracks and holes should be done with suitable repair mortars.
If necessary, the application surface is moistened with water.
Application:
25 kg. Allmax Fine is poured into a container filled with approximately 5.0-6.0 liters of water and mixed with a low speed mixer or trowel until a lump-free mixture is obtained.
During the mixture, any additives not specified in the application instructions should not be added.
The prepared mortar is 5-10 minutes. let it rest for maturation and again 1-2 minutes. It should be mixed until it becomes homogeneous.
Application thickness is applied in a single coat with a 3-10 mm thick plaster trowel.
When the plaster hardens enough, the plaster surface is trifilled and finished with a damp sponge.
Warnings:
No foreign material (lime, cement, gypsum, etc.) should be added into the prepared mortar.
Plastered surfaces should be protected from direct sunlight and heavy weather conditions in the first days, and when necessary, the plastered surfaces should be slightly wetted.
The surface applied in windy weather should be protected against rapid drying.
It is recommended to apply 2 layers in order to prevent the risk of cracking that may occur with fast drying, especially in summer applications.
Plaster nets should be used at different material joints and at points where movement is thought to be possible.
For the durability of the product, the surface should be watered at regular intervals within 3 days after application.
Do not go beyond the specified application surface and usage instructions.
All kinds of coating and painting work to be applied on the plaster applied surface should be done at least 7 days after the plaster application is completed.
Consumption: 1.5 - 1.7 kg / m² (for 1 mm thickness)
The amount of consumption is the values calculated theoretically in the laboratory environment; We recommend that consumption control sample application be made before the application.
Packing: 25 kg craft bags.
Storage and Shelf Life:
For short term storage, maximum 2 palettes should be placed on top of each other and the shipment should be made on a first in first out system.
Palettes should not be stacked on top of each other during long term storage.
Suitable storage conditions are 12 months from the date of production.
Opened packages should be stored under appropriate storage conditions and used within one week.
Safety Advices:
For more detailed information, please refer to the Safety Data Sheet.
Responsibility:
The application instructions and technical values given in this technical document are based entirely on our scientific and practical knowledge. These values may vary depending on the ambient conditions. Allmax Construction Chemicals reserves the right to make changes in products in line with technological developments. Allmax Yapı Kimyasalları cannot be held responsible for the results that may arise out of written recommendations regarding where and how the product will be used and / or due to incorrect use. Therefore, when using Allmax Construction Chemicals products, make sure that you use the right product in the right place. Allmax Construction Chemicals is only responsible for the quality of the product.
